Difference between revisions of "3D printer - Velleman K8200"
From ipswichmakerspace
(New page created for K8200) |
(Currently not in service) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
The Velleman K8200 is an opensource RepRap printer, also sold under the [https://reprap.org/wiki/3drag 3Drag] name. This printer is connected to a Raspberry Pi with [http://octoprint.org/ OctoPrint] installed. To use, plug the 3d printer and Raspberry Pi into the mains and switch on, after a minute or so the Raspberry Pi will launch the webbased OctoPi control software. Connect your computer to the Makerspace wifi and point your web browser at http://192.168.1.20. | The Velleman K8200 is an opensource RepRap printer, also sold under the [https://reprap.org/wiki/3drag 3Drag] name. This printer is connected to a Raspberry Pi with [http://octoprint.org/ OctoPrint] installed. To use, plug the 3d printer and Raspberry Pi into the mains and switch on, after a minute or so the Raspberry Pi will launch the webbased OctoPi control software. Connect your computer to the Makerspace wifi and point your web browser at http://192.168.1.20. | ||
| + | |||
| + | '''Currently NOT in service''' | ||
=== Specification === | === Specification === | ||
| Line 45: | Line 47: | ||
=== Current Issues === | === Current Issues === | ||
| − | + | None | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
=== Upgrade Plans=== | === Upgrade Plans=== | ||
; Todo | ; Todo | ||
| − | * | + | * Install RAMPS control board, Or possible a [https://www.aliexpress.com/item/BIGTREETECH-SKR-V1-3-Control-Board-32-Bit-ARM-CPU-32bit-Board-Smoothieboard-3D-Printer-Parts/32980090169.html SKR1.3] 32 bit board |
| − | + | ||
| − | + | ||
* Install new belts and tighten properly | * Install new belts and tighten properly | ||
* Consider installing second Z lead screw and motor | * Consider installing second Z lead screw and motor | ||
* Consider upgrading heated bed | * Consider upgrading heated bed | ||
| + | |||
;Complete | ;Complete | ||
* New Easy Peelsy magnetic bed surface has been installed. Please do not use scrapers on it. Clean with Isopropanol before using. | * New Easy Peelsy magnetic bed surface has been installed. Please do not use scrapers on it. Clean with Isopropanol before using. | ||
* Install new E3D hotend and direct drive Titan extruder for 1.75mm filament | * Install new E3D hotend and direct drive Titan extruder for 1.75mm filament | ||
| + | * Look at Z nut, currently has a lot of backlash. Complete, but Z flexible coupler needs replacing, new one is on order - Installed. | ||
| + | * Install new power supply - This is the next upgrade required, current power supply cannot keep the bed up to temperature - ordered. | ||
| + | |||
| + | [[Category: Equipment]] | ||
Latest revision as of 20:25, 13 October 2019
Velleman K8200
The Velleman K8200 is an opensource RepRap printer, also sold under the 3Drag name. This printer is connected to a Raspberry Pi with OctoPrint installed. To use, plug the 3d printer and Raspberry Pi into the mains and switch on, after a minute or so the Raspberry Pi will launch the webbased OctoPi control software. Connect your computer to the Makerspace wifi and point your web browser at http://192.168.1.20.
Currently NOT in service
Specification
| Build volume: | 200mm x 200mm x 200mm |
| Filament diameter: | 1.75mm |
| Nozzle diameter: | 0.4mm |
| Filament types | Most, but prefers PLA |
| Max hotend temperature: | 275 deg. C |
| Max bed temperature: | 80 deg. C |
| Hotend | Genuine E3D all metal hotend |
| Extruder | Genuine E3D Titan extruder |
- Magic numbers for Layer heights, use these for best quality:
- 0.100 mm
- 0.150 mm
- 0.175 mm
- 0.200 mm
- 0.225 mm
- 0.250 mm
- 0.275 mm
- 0.300 mm
- 0.325 mm
The Firmware has recently (20/12/2018) been updated to Marlin 1.1.9 with thermal runaway protection enabled. Certain constraints have been limited in firmware
- Maximum hot end temperature is 275 deg.C
- Maximum bed temperature is 80 deg.C
- Thermal runaway is now enabled
Current Issues
None
Upgrade Plans
- Todo
- Install RAMPS control board, Or possible a SKR1.3 32 bit board
- Install new belts and tighten properly
- Consider installing second Z lead screw and motor
- Consider upgrading heated bed
- Complete
- New Easy Peelsy magnetic bed surface has been installed. Please do not use scrapers on it. Clean with Isopropanol before using.
- Install new E3D hotend and direct drive Titan extruder for 1.75mm filament
- Look at Z nut, currently has a lot of backlash. Complete, but Z flexible coupler needs replacing, new one is on order - Installed.
- Install new power supply - This is the next upgrade required, current power supply cannot keep the bed up to temperature - ordered.
