Laser Cutters

We now have a laser cutter

Usage

Use of this equipment is stricktly for members only, before use, users MUST attend an induction. Incorrect use of this equipment can cause serious harm or death, if you are not inducted do not touch.

A user guide can be found here

Software

Software is Windows only, Windows XP through to Windows 10 is currently supported. The software required is RD Works and can be downloaded from here

The design file can be designed in almost any vector graphics program, File formats know to work are:

• dxf - Autocad, Draftsight, Inkscapce etc.

The file should be layers with layers setup for each type of cut, We would recomend three layers as follows:

• Cutting, all inner cuts
• Cutting, the outer perimeter, i.e. the last cut so the material does not fall out before all the inner cuts are complete
• Etching, anything to be etched, i.e. text and images.

Once loaded into RD Works, the layers can be ordered to ensure the outer cut is last.

Settings for common materials

1. 3mm Acrylic
   • Cut
     • Power = 30 %
     • Speed = 10mm/s
   • Etch
     • Power = 20 %
     • Speed - 200mm/s
2. 3mm ply
   • tbc
3. 6mm ply
   • tbc
4. Cardboard
   • Cut
     • Power = 30%
     • Speed = 20mm/s
     • Note that the offcuts from this fall and end up igniting later! Ensure you remove them.
     • You may need to disable the blower, to prevent embers being fanned into flames.

Text to Etch

1. Create your cutting file
2. Open in Inkscape
3. Select text (Arial Bold works well), click Path / Object to Path
4. Save as dxf, untick "use LWPOLYLINE type of line output" on the Options box
5. Import DXF file into RD Works

Materials

Materials NOT to cut

Material	DANGER!	Cause/Condequence
PVC (Poly Vinyl Chloride) vinyl pleather artificial leather	Emits chlorine gas when cut!	Don't ever cut this material as it will ruin the optics, cause the metal of the machine to corrode, and ruin the motion control system.
Thick ( >1mm ) Polycarbonate/Lexan	Cuts very poorly, discolors, catches fire	Polycarbonate is often found as flat, sheet material. The window of the laser cutter is made of Polycarbonate because polycarbonate strongly absorbs infrared radiation! This is the frequency of light the laser cutter uses to cut materials, so it is very ineffective at cutting polycarbonate. Polycarbonate is a poor choice for laser cutting.
ABS	Melts	ABS does not cut well in a laser cutter. It tends to melt rather than vaporize, and has a higher chance of catching on fire and leaving behind melted gooey deposits on the vector cutting grid. It also does not engrave well (again, tends to melt).
HDPE/milk bottle plastic	Catches fire and melts	It melts. It gets gooey. Don't use it.
PolyStyrene Foam	Catches fire	It catches fire, it melts, and only thin pieces cut. This is the #1 material that causes laser fires!!!
PolyPropylene Foam	Catches fire	Like PolyStyrene, it melts, catches fire, and the melted drops continue to burn and turn into rock-hard drips and pebbles.
Fiberglass	Emits fumes	It's a mix of two materials that cant' be cut. Glass (etch, no cut) and epoxy resin (fumes)
Coated Carbon Fiber	Emits noxious fumesmits noxious fumes	A mix of two materials. Thin carbon fiber mat can be cut, with some fraying - but not when coated.

Laser safe materials

The laser can cut or etch. The materials that the laser can cut materials like wood, paper, cork, and some kinds of plastics. Etching can be done on almost anything, wood, cardboard, aluminum, stainless steel, plastic, marble, stone, tile, and glass.

Cutting

Material	Max thickness	Notes	WARNINGS!
Many woods	6mm (1/4")	Avoid oily/resinous woods	Be very careful about cutting oily woods, or very resinous woods as they also may catch fire.
Plywood/Composite woods	6mm (1/4")	These contain glue, and may not laser cut as well as solid wood.
MDF/Engineered woods	6mm (1/4")	These are okay to use but may experience a higher amount of charring when cut.
Paper, card stock	thin	Cuts very well on the laser cutter, and also very quickly.
Cardboard, carton	thicker	Cuts well but may catch fire. Remove all fragments! Blower may need disabling.	Watch for fire.
Cork	6mm (1/4")	Cuts nicely, but the quality of the cut depends on the thickness and quality of the cork. Engineered cork has a lot of glue in it, and may not cut as well.	Avoid thicker cork.
Acrylic/Lucite/Plexiglas/PMMA	12mm (1/2")	Cuts extremely well leaving a beautifully polished edge.
Thin Polycarbonate Sheeting (<1mm)	<1mm	Very thin polycarbonate can be cut, but tends to discolor badly. Extremely thin sheets (0.5mm and less) may cut with yellowed/discolored edges. Polycarbonate absorbs IR strongly, and is a poor material to use in the laser cutter.	Watch for smoking/burning
Delrin (POM)	thin	Delrin comes in a number of shore strengths (hardness) and the harder Delrin tends to work better. Great for gears!
Kapton tape (Polyimide)	1.5mm (1/16")	Works well, in thin sheets and strips like tape.
Mylar	1.5mm (1/16")	Works well if it's thin. Thick mylar has a tendency to warp, bubble, and curl	Gold coated mylar will not work.
Solid Styrene	1.5mm (1/16")	Smokes a lot when cut, but can be cut.	Keep it thin.
Depron foam	6mm (1/4")	Used a lot for hobby, RC aircraft, architectural models, and toys. 1/4" cuts nicely, with a smooth edge.	Must be constantly monitored.
Gator foam		Foam core gets burned and eaten away compared to the top and bottom hard paper shell.	Not a fantastic thing to cut, but it can be cut if watched.
Cloth/felt/hemp/cotton		They all cut well. Our lasers can be used in lace-making.	Not plastic coated or impregnated cloth!
Leather/Suede	3mm (1/8")	Leather is very hard to cut, but can be if it's thinner than a belt (call it 1/8"). Our "Advanced" laser training class covers this.	Real leather only! Not 'pleather' or other imitations!
Magnetic Sheet		Cuts beautifully
NON-CHLORINE-containing rubber		Fine for cutting.	Beware chlorine-containing rubber!
Teflon (PTFE)	thin	Cuts OK in thin sheets. See https://www.ulsinc.com/materials/teflon ; the issues listed in https://en.wikipedia.org/wiki/Polymer_fume_fever should not matter because our lasers are fully vented and exhausted.
Carbon fiber mats/weave that has not had epoxy applied		Can be cut, very slowly.	You must not cut carbon fiber that has been coated!!
Coroplast ('corrugated plastic')	6mm (1/4")	Difficult because of the vertical strips. Three passes at 80% power, 7% speed, and it will be slightly connected still at the bottom from the vertical strips.

Etching

All the above "cuttable" materials can be etched, in some cases very deeply.

In addition, you can etch:

Material	Notes	WARNINGS!
Glass	Green seems to work best...looks sandblasted.	Only FLAT GLASS can be engraved in our cutter. No round or cylindrical items.
Ceramic tile
Anodized aluminum	Vaporizes the anodization away.
Painted/coated metals	Vaporizes the paint away.
Stone, Marble, Granite, Soapstone, Onyx.	Gets a white "textured" look when etched.	100% power, 50% speed or less works well for etching.

Photo style engraving of mdf, this was my process

Import image

Select it then hit the BMP button middle top

Set dpi to 300 Set dither Set net graphic 100 lines,

Preview on view, if okay then apply to source

Set min power to say 25% max power 50% speed 200mm, worked for mdf, with good results

Test files

We have carried out a number of tests on common materials, we will publish the settings is the software section above, if you wish to carry out further tests, the test files can be downloaded from Boss Laser.

Suppliers of materials

Kitronic

Other Learning Resources

YouTube play list